Bolt pattern, center bore, factory wheel sizes for each submodel and the aftermarket widths and offsets that bolt on to the Chevrolet Corvette built from 2020 to 2026 (Stingray, E-Ray, Z06, ZR1, ZR1X).
Every 2020-2026 Chevrolet Corvette uses a 5X120 bolt pattern with a 66.9 mm hub (center bore). Most aftermarket wheels are machined with a larger bore so one wheel can fit many cars; fit hub-centric rings with a 66.9 mm inner diameter so the wheel centers on the hub instead of the lugs. Lug thread is M14x1.5. Torque the lugs to the figure in your owner's manual and re-check them after the first 50 miles.
US-market submodels of the Chevrolet Corvette (C8) and the model years each was sold. All of them share the 5X120 bolt pattern.
| Submodel | Years | Factory wheel sizes |
|---|---|---|
| Stingray | 2020-2026 | See factory sizes below |
| E-Ray | 2024-2026 | 20x10 +35 front / 21x13 +40 rear |
| Z06 | 2023-2026 | 20x10 +35 front / 21x13 +40 rear |
| ZR1 | 2025-2026 | 20x10 +35 front / 21x13 +40 rear |
| ZR1X | 2026 | 20x10 +35 front / 21x13 +40 rear |
Wheel sizes Chevrolet fitted to the 2020-2026 Chevrolet Corvette from the factory (all submodels; the table above lists them by submodel). Offsets are ET in millimeters.
| Factory size |
|---|
| 19x8.5 +52 front / 20x11 +64 rear |
| 19x10 +43 front / 20x12 +59 rear |
| 20x10 +35 front / 21x13 +40 rear |
Widths and offsets with Verified Fitment on the 2020-2026 Chevrolet Corvette: no fender rolling, spacers or camber changes, and the wheel sits like the factory one or a little further out. Offsets outside a range below either rub, poke past the fender or sit tucked in. Test-fit one wheel for brake and suspension clearance before mounting tires.
| Diameter | Width | Front offset | Rear offset |
|---|---|---|---|
| 19-21" | 8.5" | -1 to +59 | — |
| 19-21" | 9" | +5 to +53 | — |
| 19-21" | 9.5" | +11 to +47 | — |
| 19-21" | 10" | +18 to +40 | — |
| 19-21" | 10.5" | +24 to +34 | — |
| 19-21" | 11" | — | +45 to +69 |
| 19-21" | 11.5" | — | +51 to +63 |
| 19-21" | 12" | — | +57 |
Wider still: 19x12.5 front — / rear +45 to +56; 20x12.5 front — / rear +45 to +56; 21x12.5 front — / rear +45 to +56 fit with modifications (roll the fender lips, add negative camber (camber bolts or arms), wheel alignment after install).
| Diameter | Width | Front offset | Rear offset |
|---|---|---|---|
| 20-21" | 10" | +18 to +40 | — |
| 20-21" | 10.5" | +24 to +34 | — |
| 21" | 13" | — | +40 to +44 |
In-stock PG WHEELS sets in sizes with Verified Fitment for the 2020-2026 Chevrolet Corvette. Each card shows only the sizes that fit; prices are for a set of 4 with free shipping in the lower 48.
Modifications Required (roll the fender lips, add negative camber (camber bolts or arms), wheel alignment after install)
The 2020-2026 Chevrolet Corvette (C8) uses a 5X120 bolt pattern and a 66.9 mm center bore.
Factory sizes: 19x8.5 +52 front / 20x11 +64 rear; 19x10 +43 front / 20x12 +59 rear; 20x10 +35 front / 21x13 +40 rear.
Its wheel fasteners use a M14x1.5 thread.
Bolt-on sizes run from 19" to 21" in diameter; see the size table for the offset range at each width.