Dodge Charger (LX) 2006-2010 Wheel Fitment Guide

Bolt pattern, center bore, factory wheel sizes for each submodel and the aftermarket widths and offsets that bolt on to the Dodge Charger built from 2006 to 2010 (SE, SXT, R/T, Daytona R/T, SRT8).

Fitment specs

Bolt pattern5X115
Center bore71.5 mm
Lug threadM14x1.5
Model years2006-2010
GenerationLX

Every 2006-2010 Dodge Charger uses a 5X115 bolt pattern with a 71.5 mm hub (center bore). Most aftermarket wheels are machined with a larger bore so one wheel can fit many cars; fit hub-centric rings with a 71.5 mm inner diameter so the wheel centers on the hub instead of the lugs. Lug thread is M14x1.5. Torque the lugs to the figure in your owner's manual and re-check them after the first 50 miles.

Years & submodels

US-market submodels of the Dodge Charger (LX) and the model years each was sold. All of them share the 5X115 bolt pattern.

SubmodelYearsFactory wheel sizes
SE2006-201017x7 +22
SXT2006-201017x7 +22
R/T2006-201018x7.5 +24
18x8 +24
Daytona R/T2006-200918x7.5 +24
20x8 +24
SRT82006-201020x8 +24

Factory wheel sizes

Wheel sizes Dodge fitted to the 2006-2010 Dodge Charger from the factory (all submodels; the table above lists them by submodel). Offsets are ET in millimeters.

Factory size
17x7 +22
17x7.5 +24
18x7.5 +24
18x8 +24
19x7.5 +24
19x8.5 +25
20x8 +24
21x8.5 +25
22x9 +20

Aftermarket sizes that bolt on

Widths and offsets with Verified Fitment on the 2006-2010 Dodge Charger: no fender rolling, spacers or camber changes, and the wheel sits like the factory one or a little further out. Offsets outside a range below either rub, poke past the fender or sit tucked in. Test-fit one wheel for brake and suspension clearance before mounting tires.

SE, SXT

DiameterWidthFront offsetRear offset
17-20"7"-5 to +32-14 to +32
17-20"7.5"+1 to +38-7 to +38
17-20"8"+8 to +32-1 to +45
17-20"8.5"+14 to +26+5 to +43
17-20"9"+20+12 to +36
17-20"9.5"—+18 to +30
17-20"10"—+24

Wider still: 17x10.5 front — / rear +21 to +24; 18x10.5 front — / rear +21 to +24; 19x10.5 front — / rear +21 to +24; 20x10.5 front — / rear +21 to +24 fit with modifications (roll the fender lips, add negative camber (camber bolts or arms), wheel alignment after install).

R/T, Daytona R/T

DiameterWidthFront offsetRear offset
18-20"7.5"+1 to +34-7 to +34
18-20"8"+8 to +32-1 to +40
18-20"8.5"+14 to +26+5 to +43
18-20"9"+20+12 to +36
18-20"9.5"—+18 to +30
18-20"10"—+24

Wider still: 18x10.5 front — / rear +21 to +24; 19x10.5 front — / rear +21 to +24; 20x10.5 front — / rear +21 to +24 fit with modifications (roll the fender lips, add negative camber (camber bolts or arms), wheel alignment after install).

SRT8

DiameterWidthFront offsetRear offset
20"8"+8 to +32-1 to +34
20"8.5"+14 to +26+5 to +40
20"9"+20+12 to +36
20"9.5"—+18 to +30
20"10"—+24

Wider still: 20x10.5 front — / rear +21 to +24 fit with modifications (roll the fender lips, add negative camber (camber bolts or arms), wheel alignment after install).

FAQ

What is the bolt pattern of the 2006-2010 Dodge Charger?

The 2006-2010 Dodge Charger (LX) uses a 5X115 bolt pattern and a 71.5 mm center bore.

What size wheels came on the 2006-2010 Dodge Charger from the factory?

Factory sizes: 17x7 +22; 17x7.5 +24; 18x7.5 +24; 18x8 +24; 19x7.5 +24; 19x8.5 +25; 20x8 +24; 21x8.5 +25; 22x9 +20.

What lug thread size does the 2006-2010 Dodge Charger use?

Its wheel fasteners use a M14x1.5 thread.

What aftermarket wheel sizes fit the 2006-2010 Dodge Charger without modifications?

Bolt-on sizes run from 17" to 20" in diameter; see the size table for the offset range at each width.