Ford Explorer (U251) 2006-2010 Wheel Fitment Guide

Bolt pattern, center bore, factory wheel sizes for each submodel and the aftermarket widths and offsets that bolt on to the Ford Explorer built from 2006 to 2010 (XLT, Eddie Bauer, Limited).

Fitment specs

Bolt pattern5X114.3
Center bore70.5 mm
Lug thread1/2"-20UNF
Model years2006-2010
GenerationU251

Every 2006-2010 Ford Explorer uses a 5X114.3 bolt pattern with a 70.5 mm hub (center bore). Most aftermarket wheels are machined with a larger bore so one wheel can fit many cars; fit hub-centric rings with a 70.5 mm inner diameter so the wheel centers on the hub instead of the lugs. Lug thread is 1/2"-20UNF. Torque the lugs to the figure in your owner's manual and re-check them after the first 50 miles.

Years & submodels

US-market submodels of the Ford Explorer (U251) and the model years each was sold. All of them share the 5X114.3 bolt pattern.

SubmodelYearsFactory wheel sizes
XLT2006-201016x6.5 +47
16x7 +44
Eddie Bauer2006-201016x7 +12
17x7.5 +44
Limited2006-201016x7 +12
17x7.5 +44
18x7.5 +44

Factory wheel sizes

Wheel sizes Ford fitted to the 2006-2010 Ford Explorer from the factory (all submodels; the table above lists them by submodel). Offsets are ET in millimeters.

Factory size
16x6.5 +47
16x7 +44
17x7.5 +44
18x7.5 +44
20x8 +35

Aftermarket sizes that bolt on

Widths and offsets with Verified Fitment on the 2006-2010 Ford Explorer: no fender rolling, spacers or camber changes, and the wheel sits like the factory one or a little further out. Offsets outside a range below either rub, poke past the fender or sit tucked in. Test-fit one wheel for brake and suspension clearance before mounting tires.

XLT

DiameterWidthOffset range
16-20"6.5"+30 to +52
16-20"7"+36 to +46

Wider still: 16x8 +28 to +39; 17x8 +28 to +39; 18x8 +28 to +39; 19x8 +28 to +39; 20x8 +28 to +39 fit with modifications (leveling kit or small lift for larger tires, trim front fender liner and air dam, check upper control arm / sway bar clearance).

Eddie Bauer, Limited

DiameterWidthOffset range
16-20"7"+12 to +22
16-20"7.5"+19 to +28

Wider still: 16x8 +25 to +39; 16x8.5 +32 to +33; 17x8 +25 to +39; 17x8.5 +32 to +33; 18x8 +25 to +39; 18x8.5 +32 to +33… fit with modifications (leveling kit or small lift for larger tires, trim front fender liner and air dam, check upper control arm / sway bar clearance).

Wheels in stock that fit

In-stock PG WHEELS sets in sizes with Verified Fitment for the 2006-2010 Ford Explorer. Each card shows only the sizes that fit; prices are for a set of 4 with free shipping in the lower 48.

XLT

Modifications Required (leveling kit or small lift for larger tires, trim front fender liner and air dam, check upper control arm / sway bar clearance)

Eddie Bauer, Limited

Modifications Required (leveling kit or small lift for larger tires, trim front fender liner and air dam, check upper control arm / sway bar clearance)

FAQ

What is the bolt pattern of the 2006-2010 Ford Explorer?

The 2006-2010 Ford Explorer (U251) uses a 5X114.3 bolt pattern and a 70.5 mm center bore.

What size wheels came on the 2006-2010 Ford Explorer from the factory?

Factory sizes: 16x6.5 +47; 16x7 +44; 17x7.5 +44; 18x7.5 +44; 20x8 +35.

What lug thread size does the 2006-2010 Ford Explorer use?

Its wheel fasteners use a 1/2"-20UNF thread.

What aftermarket wheel sizes fit the 2006-2010 Ford Explorer without modifications?

Bolt-on sizes run from 16" to 20" in diameter; see the size table for the offset range at each width.