Honda CR-V (RD1) 1997-2001 Wheel Fitment Guide

Bolt pattern, center bore, factory wheel sizes for each submodel and the aftermarket widths and offsets that bolt on to the Honda CR-V built from 1997 to 2001 (Base, LX, EX, SE).

Fitment specs

Bolt pattern5X114.3
Center bore64.1 mm
Lug threadM12x1.5
Model years1997-2001
GenerationRD1

Every 1997-2001 Honda CR-V uses a 5X114.3 bolt pattern with a 64.1 mm hub (center bore). Most aftermarket wheels are machined with a larger bore so one wheel can fit many cars; fit hub-centric rings with a 64.1 mm inner diameter so the wheel centers on the hub instead of the lugs. Lug thread is M12x1.5. Torque the lugs to the figure in your owner's manual and re-check them after the first 50 miles.

Years & submodels

US-market submodels of the Honda CR-V (RD1) and the model years each was sold. All of them share the 5X114.3 bolt pattern.

SubmodelYearsFactory wheel sizes
Base1997See factory sizes below
LX1997-200115x6 +50
EX1998-200115x6 +50
SE2001See factory sizes below

Factory wheel sizes

Wheel sizes Honda fitted to the 1997-2001 Honda CR-V from the factory (all submodels; the table above lists them by submodel). Offsets are ET in millimeters.

Factory size
15x6 +50
15x6.5 +45
16x6.5 +45
16x7 +42
17x6.5 +45
17x7 +40
17x7 +42
18x7.5 +40

Aftermarket sizes that bolt on

Widths and offsets with Verified Fitment on the 1997-2001 Honda CR-V: no fender rolling, spacers or camber changes, and the wheel sits like the factory one or a little further out. Offsets outside a range below either rub, poke past the fender or sit tucked in. Test-fit one wheel for brake and suspension clearance before mounting tires.

DiameterWidthOffset range
15-18"6"+33 to +55
15-18"6.5"+39 to +49

Wider still: 15x7.5 +31 to +42; 16x7.5 +31 to +42; 17x7.5 +31 to +42; 18x7.5 +31 to +42 fit with modifications (trim front bumper cover / inner fender liner at full lock, roll rear fender lips, hub-centric rings for aftermarket wheels).

Wheels in stock that fit

In-stock PG WHEELS sets in sizes with Verified Fitment for the 1997-2001 Honda CR-V. Each card shows only the sizes that fit; prices are for a set of 4 with free shipping in the lower 48.

Modifications Required (trim front bumper cover / inner fender liner at full lock, roll rear fender lips, hub-centric rings for aftermarket wheels)

FAQ

What is the bolt pattern of the 1997-2001 Honda CR-V?

The 1997-2001 Honda CR-V (RD1) uses a 5X114.3 bolt pattern and a 64.1 mm center bore.

What size wheels came on the 1997-2001 Honda CR-V from the factory?

Factory sizes: 15x6 +50; 15x6.5 +45; 16x6.5 +45; 16x7 +42; 17x6.5 +45; 17x7 +40; 17x7 +42; 18x7.5 +40.

What lug thread size does the 1997-2001 Honda CR-V use?

Its wheel fasteners use a M12x1.5 thread.

What aftermarket wheel sizes fit the 1997-2001 Honda CR-V without modifications?

Bolt-on sizes run from 15" to 18" in diameter; see the size table for the offset range at each width.