Honda Odyssey (RL3) 2008-2010 Wheel Fitment Guide

Bolt pattern, center bore, factory wheel sizes for each submodel and the aftermarket widths and offsets that bolt on to the Honda Odyssey built from 2008 to 2010 (LX, EX, EX-L, Touring).

Fitment specs

Bolt pattern5X120
Center bore64.1 mm
Lug threadM14x1.5
Model years2008-2010
GenerationRL3

Every 2008-2010 Honda Odyssey uses a 5X120 bolt pattern with a 64.1 mm hub (center bore). Most aftermarket wheels are machined with a larger bore so one wheel can fit many cars; fit hub-centric rings with a 64.1 mm inner diameter so the wheel centers on the hub instead of the lugs. Lug thread is M14x1.5. Torque the lugs to the figure in your owner's manual and re-check them after the first 50 miles.

Years & submodels

US-market submodels of the Honda Odyssey (RL3) and the model years each was sold. All of them share the 5X120 bolt pattern.

SubmodelYearsFactory wheel sizes
LX2008-201016x7 +50
EX2008-201016x7 +50
EX-L2008-201016x7 +50
Touring2008-201017x7 +50

Factory wheel sizes

Wheel sizes Honda fitted to the 2008-2010 Honda Odyssey from the factory (all submodels; the table above lists them by submodel). Offsets are ET in millimeters.

Factory size
16x7 +50
17x7 +50
18x7.5 +50
19x8 +45

Aftermarket sizes that bolt on

Widths and offsets with Verified Fitment on the 2008-2010 Honda Odyssey: no fender rolling, spacers or camber changes, and the wheel sits like the factory one or a little further out. Offsets outside a range below either rub, poke past the fender or sit tucked in. Test-fit one wheel for brake and suspension clearance before mounting tires.

LX, EX, EX-L

DiameterWidthOffset range
16-20"7"+33 to +55
16-20"7.5"+39 to +49

Wider still: 16x8.5 +31 to +42; 17x8.5 +31 to +42; 18x8.5 +31 to +42; 19x8.5 +31 to +42; 20x8.5 +31 to +42 fit with modifications (roll rear fender lips, trim front inner fender liner at full lock, hub-centric rings for aftermarket wheels).

Touring

DiameterWidthOffset range
17-20"7"+33 to +55
17-20"7.5"+39 to +49

Wider still: 17x8.5 +31 to +42; 18x8.5 +31 to +42; 19x8.5 +31 to +42; 20x8.5 +31 to +42 fit with modifications (roll rear fender lips, trim front inner fender liner at full lock, hub-centric rings for aftermarket wheels).

Wheels in stock that fit

In-stock PG WHEELS sets in sizes with Verified Fitment for the 2008-2010 Honda Odyssey. Each card shows only the sizes that fit; prices are for a set of 4 with free shipping in the lower 48.

LX, EX, EX-L

Modifications Required (roll rear fender lips, trim front inner fender liner at full lock, hub-centric rings for aftermarket wheels)

Touring

Modifications Required (roll rear fender lips, trim front inner fender liner at full lock, hub-centric rings for aftermarket wheels)

FAQ

What is the bolt pattern of the 2008-2010 Honda Odyssey?

The 2008-2010 Honda Odyssey (RL3) uses a 5X120 bolt pattern and a 64.1 mm center bore.

What size wheels came on the 2008-2010 Honda Odyssey from the factory?

Factory sizes: 16x7 +50; 17x7 +50; 18x7.5 +50; 19x8 +45.

What lug thread size does the 2008-2010 Honda Odyssey use?

Its wheel fasteners use a M14x1.5 thread.

What aftermarket wheel sizes fit the 2008-2010 Honda Odyssey without modifications?

Bolt-on sizes run from 16" to 20" in diameter; see the size table for the offset range at each width.