Bolt pattern, center bore, factory wheel sizes and the aftermarket widths and offsets that bolt on to the Mazda Mazda3 built from 2010 to 2013 (i SV, i Sport, i Touring, i Grand Touring, s Sport, s Touring, s Grand Touring, Mazdaspeed3).
Every 2010-2013 Mazda Mazda3 uses a 5X114.3 bolt pattern with a 67.1 mm hub (center bore). Most aftermarket wheels are machined with a larger bore so one wheel can fit many cars; fit hub-centric rings with a 67.1 mm inner diameter so the wheel centers on the hub instead of the lugs. Lug thread is M12x1.5. Torque the lugs to the figure in your owner's manual and re-check them after the first 50 miles.
US-market submodels of the Mazda Mazda3 (BL) and the model years each was sold. All of them share the 5X114.3 bolt pattern.
| Submodel | Years |
|---|---|
| i SV | 2010-2013 |
| i Sport | 2010-2013 |
| i Touring | 2010-2013 |
| i Grand Touring | 2012-2013 |
| s Sport | 2010-2013 |
| s Touring | 2010-2013 |
| s Grand Touring | 2010-2013 |
| Mazdaspeed3 | 2010-2013 |
Wheel sizes Mazda fitted to the 2010-2013 Mazda Mazda3 from the factory. Offsets are ET in millimeters.
| Factory size |
|---|
| 15x6 +50 |
| 16x6.5 +50 |
| 17x6.5 +50 |
| 17x7 +52.5 |
| 17x7.5 +52 |
| 18x7 +50 |
| 18x7.5 +52 |
| 19x8 +48 |
| 18x7.5 +52.5 |
Widths and offsets with Verified Fitment on the 2010-2013 Mazda Mazda3: no fender rolling, spacers or camber changes, and the wheel sits like the factory one or a little further out. Offsets outside a range below either rub, poke past the fender or sit tucked in. Test-fit one wheel for brake and suspension clearance before mounting tires.
| Diameter | Width | Offset range |
|---|---|---|
| 15-19" | 6" | +16 to +60 |
| 15-19" | 6.5" | +23 to +66 |
| 15-19" | 7" | +29 to +64 |
| 15-19" | 7.5" | +35 to +58 |
| 15-19" | 8" | +42 to +52 |
Wider still: 15x9 +34 to +45; 16x9 +34 to +45; 17x9 +34 to +45; 18x9 +34 to +45; 19x9 +34 to +45 fit with modifications (roll the fender lips, add negative camber (camber bolts or arms), wheel alignment after install).
In-stock PG WHEELS sets in sizes with Verified Fitment for the 2010-2013 Mazda Mazda3. Each card shows only the sizes that fit; prices are for a set of 4 with free shipping in the lower 48.
Modifications Required (roll the fender lips, add negative camber (camber bolts or arms), wheel alignment after install)












The 2010-2013 Mazda Mazda3 (BL) uses a 5X114.3 bolt pattern and a 67.1 mm center bore.
Factory sizes: 15x6 +50; 16x6.5 +50; 17x6.5 +50; 17x7 +52.5; 17x7.5 +52; 18x7 +50; 18x7.5 +52; 19x8 +48; 18x7.5 +52.5.
Its wheel fasteners use a M12x1.5 thread.
Bolt-on sizes run from 15" to 19" in diameter; see the size table for the offset range at each width.