Bolt pattern, center bore, factory wheel sizes for each submodel and the aftermarket widths and offsets that bolt on to the Mercedes-Benz CL-Class built from 1998 to 1999 (CL500, CL600).
Every 1998-1999 Mercedes-Benz CL-Class uses a 5X112 bolt pattern with a 66.6 mm hub (center bore). Most aftermarket wheels are machined with a larger bore so one wheel can fit many cars; fit hub-centric rings with a 66.6 mm inner diameter so the wheel centers on the hub instead of the lugs. Lug thread is M14x1.5. Torque the lugs to the figure in your owner's manual and re-check them after the first 50 miles.
US-market submodels of the Mercedes-Benz CL-Class (C140) and the model years each was sold. All of them share the 5X112 bolt pattern.
| Submodel | Years | Factory wheel sizes |
|---|---|---|
| CL500 | 1998-1999 | 18x8.5 +47 18x8.5 +45 front / 18x9.5 +55 rear 19x8.5 +40 front / 19x10 +50 rear |
| CL600 | 1998-1999 | 18x8.5 +47 18x8.5 +45 front / 18x9.5 +55 rear 18x9.5 +55 19x9 +40 front / 19x10 +50 rear 19x10 +50 |
Wheel sizes Mercedes-Benz fitted to the 1998-1999 Mercedes-Benz CL-Class from the factory (all submodels; the table above lists them by submodel). Offsets are ET in millimeters.
| Factory size |
|---|
| 16x7.5 +51 |
| 17x8 +50 |
| 18x8.5 +47 |
| 18x8.5 +45 front / 18x9.5 +55 rear |
| 18x9.5 +55 |
| 19x8.5 +40 front / 19x10 +50 rear |
| 19x9 +45 |
| 19x9 +40 front / 19x10 +50 rear |
| 19x10 +50 |
Widths and offsets with Verified Fitment on the 1998-1999 Mercedes-Benz CL-Class: no fender rolling, spacers or camber changes, and the wheel sits like the factory one or a little further out. Offsets outside a range below either rub, poke past the fender or sit tucked in. Test-fit one wheel for brake and suspension clearance before mounting tires.
| Diameter | Width | Front offset | Rear offset |
|---|---|---|---|
| 18-19" | 8.5" | +28 to +52 | +30 to +52 |
| 18-19" | 9" | +34 to +46 | +36 to +46 |
Wider still: 18x10 front +26 to +39 / rear +28 to +39; 18x10.5 front +33 / rear —; 19x10 front +26 to +39 / rear +28 to +39; 19x10.5 front +33 / rear — fit with modifications (roll rear fender lips, adjustable camber parts for extra negative camber, hub-centric rings (66.6 mm), correct-length ball-seat lug bolts).
In-stock PG WHEELS sets in sizes with Verified Fitment for the 1998-1999 Mercedes-Benz CL-Class. Each card shows only the sizes that fit; prices are for a set of 4 with free shipping in the lower 48.












Modifications Required (roll rear fender lips, adjustable camber parts for extra negative camber, hub-centric rings (66.6 mm), correct-length ball-seat lug bolts)











The 1998-1999 Mercedes-Benz CL-Class (C140) uses a 5X112 bolt pattern and a 66.6 mm center bore.
Factory sizes: 16x7.5 +51; 17x8 +50; 18x8.5 +47; 18x8.5 +45 front / 18x9.5 +55 rear; 18x9.5 +55; 19x8.5 +40 front / 19x10 +50 rear; 19x9 +45; 19x9 +40 front / 19x10 +50 rear; 19x10 +50.
Its wheel fasteners use a M14x1.5 thread.
Bolt-on sizes run from 18" to 19" in diameter; see the size table for the offset range at each width.