Bolt pattern, center bore, factory wheel sizes for each submodel and the aftermarket widths and offsets that bolt on to the Mercedes-Benz M-Class built from 1998 to 2005 (ML320, ML350, ML430, ML500, ML55 AMG).
Every 1998-2005 Mercedes-Benz M-Class uses a 5X112 bolt pattern with a 66.6 mm hub (center bore). Most aftermarket wheels are machined with a larger bore so one wheel can fit many cars; fit hub-centric rings with a 66.6 mm inner diameter so the wheel centers on the hub instead of the lugs. Lug thread is M14x1.5. Torque the lugs to the figure in your owner's manual and re-check them after the first 50 miles.
US-market submodels of the Mercedes-Benz M-Class (W163) and the model years each was sold. All of them share the 5X112 bolt pattern.
| Submodel | Years | Factory wheel sizes |
|---|---|---|
| ML320 | 1998-2003 | 16x6.5 +47 16x8 +62 17x8 +52 17x8.5 +47 17x8.5 +52 18x9 +52 |
| ML350 | 2003-2005 | 17x8 +52 17x8.5 +47 17x8.5 +52 18x9 +52 |
| ML430 | 1999-2001 | 17x8 +52 17x8.5 +47 17x8.5 +52 18x9 +52 |
| ML500 | 2002-2005 | 17x8 +52 17x8.5 +47 17x8.5 +52 18x9 +52 |
| ML55 AMG | 2000-2003 | See factory sizes below |
Wheel sizes Mercedes-Benz fitted to the 1998-2005 Mercedes-Benz M-Class from the factory (all submodels; the table above lists them by submodel). Offsets are ET in millimeters.
| Factory size |
|---|
| 16x6.5 +47 |
| 16x8 +62 |
| 17x8 +52 |
| 17x8.5 +47 |
| 17x8.5 +52 |
| 18x9 +52 |
Widths and offsets with Verified Fitment on the 1998-2005 Mercedes-Benz M-Class: no fender rolling, spacers or camber changes, and the wheel sits like the factory one or a little further out. Offsets outside a range below either rub, poke past the fender or sit tucked in. Test-fit one wheel for brake and suspension clearance before mounting tires.
| Diameter | Width | Offset range |
|---|---|---|
| 16-19" | 6.5" | +16 to +57 |
| 16-19" | 7" | +22 to +63 |
| 16-19" | 7.5" | +29 to +64 |
| 16-19" | 8" | +35 to +57 |
| 16-19" | 8.5" | +41 to +51 |
Wider still: 16x9.5 +33 to +44; 17x9.5 +33 to +44; 18x9.5 +33 to +44; 19x9.5 +33 to +44 fit with modifications (trim front wheel-well liner / bumper cover tabs, hub-centric rings (66.6 mm), check strut and spring clearance on the inner edge, longer ball-seat lug bolts with spacers).
| Diameter | Width | Offset range |
|---|---|---|
| 17-19" | 8" | +35 to +57 |
| 17-19" | 8.5" | +41 to +51 |
Wider still: 17x9.5 +33 to +44; 18x9.5 +33 to +44; 19x9.5 +33 to +44 fit with modifications (trim front wheel-well liner / bumper cover tabs, hub-centric rings (66.6 mm), check strut and spring clearance on the inner edge, longer ball-seat lug bolts with spacers).
In-stock PG WHEELS sets in sizes with Verified Fitment for the 1998-2005 Mercedes-Benz M-Class. Each card shows only the sizes that fit; prices are for a set of 4 with free shipping in the lower 48.








Modifications Required (trim front wheel-well liner / bumper cover tabs, hub-centric rings (66.6 mm), check strut and spring clearance on the inner edge, longer ball-seat lug bolts with spacers)



















Modifications Required (trim front wheel-well liner / bumper cover tabs, hub-centric rings (66.6 mm), check strut and spring clearance on the inner edge, longer ball-seat lug bolts with spacers)












The 1998-2005 Mercedes-Benz M-Class (W163) uses a 5X112 bolt pattern and a 66.6 mm center bore.
Factory sizes: 16x6.5 +47; 16x8 +62; 17x8 +52; 17x8.5 +47; 17x8.5 +52; 18x9 +52.
Its wheel fasteners use a M14x1.5 thread.
Bolt-on sizes run from 16" to 19" in diameter; see the size table for the offset range at each width.