Bolt pattern, center bore, factory wheel sizes for each submodel and the aftermarket widths and offsets that bolt on to the Mercedes-Benz E-Class built from 1994 to 1995 (E300 Diesel, E320, E420, E500).
Every 1994-1995 Mercedes-Benz E-Class uses a 5X112 bolt pattern with a 66.6 mm hub (center bore). Most aftermarket wheels are machined with a larger bore so one wheel can fit many cars; fit hub-centric rings with a 66.6 mm inner diameter so the wheel centers on the hub instead of the lugs. Lug thread is M12x1.5. Torque the lugs to the figure in your owner's manual and re-check them after the first 50 miles.
US-market submodels of the Mercedes-Benz E-Class (W124) and the model years each was sold. All of them share the 5X112 bolt pattern.
| Submodel | Years | Factory wheel sizes |
|---|---|---|
| E300 Diesel | 1995 | See factory sizes below |
| E320 | 1994-1995 | 16x7 +46 16x7.5 +42 17x7 +46 17x7.5 +42 18x8 +42 |
| E420 | 1994-1995 | 16x7 +46 16x7.5 +42 17x7 +46 17x7.5 +42 18x8 +42 |
| E500 | 1994 | 16x8 +34 17x8.5 +34 18x9 +30 |
Wheel sizes Mercedes-Benz fitted to the 1994-1995 Mercedes-Benz E-Class from the factory (all submodels; the table above lists them by submodel). Offsets are ET in millimeters.
| Factory size |
|---|
| 15x6.5 +44 |
| 15x6.5 +48 |
| 15x7 +41 |
| 16x7 +46 |
| 16x7.5 +42 |
| 16x8 +34 |
| 17x7 +46 |
| 17x7.5 +42 |
| 17x8.5 +34 |
| 18x8 +42 |
| 18x9 +30 |
Widths and offsets with Verified Fitment on the 1994-1995 Mercedes-Benz E-Class: no fender rolling, spacers or camber changes, and the wheel sits like the factory one or a little further out. Offsets outside a range below either rub, poke past the fender or sit tucked in. Test-fit one wheel for brake and suspension clearance before mounting tires.
| Diameter | Width | Offset range |
|---|---|---|
| 15-17" | 6.5" | -2 to +54 |
| 15-17" | 7" | +4 to +52 |
| 15-17" | 7.5" | +11 to +46 |
| 15-17" | 8" | +17 to +39 |
| 15-17" | 8.5" | +23 to +33 |
Wider still: 15x9.5 +15 to +26; 16x9.5 +15 to +26; 17x9.5 +15 to +26 fit with modifications (roll rear fender lips, adjustable camber parts for extra negative camber, hub-centric rings (66.6 mm), correct-length ball-seat lug bolts).
| Diameter | Width | Offset range |
|---|---|---|
| 16-18" | 7" | +4 to +52 |
| 16-18" | 7.5" | +11 to +46 |
| 16-18" | 8" | +17 to +39 |
| 16-18" | 8.5" | +23 to +33 |
Wider still: 16x9.5 +15 to +26; 17x9.5 +15 to +26; 18x9.5 +15 to +26 fit with modifications (roll rear fender lips, adjustable camber parts for extra negative camber, hub-centric rings (66.6 mm), correct-length ball-seat lug bolts).
| Diameter | Width | Offset range |
|---|---|---|
| 16-18" | 8" | +17 to +39 |
| 16-18" | 8.5" | +23 to +33 |
Wider still: 16x9.5 +15 to +26; 17x9.5 +15 to +26; 18x9.5 +15 to +26 fit with modifications (roll rear fender lips, adjustable camber parts for extra negative camber, hub-centric rings (66.6 mm), correct-length ball-seat lug bolts).
In-stock PG WHEELS sets in sizes with Verified Fitment for the 1994-1995 Mercedes-Benz E-Class. Each card shows only the sizes that fit; prices are for a set of 4 with free shipping in the lower 48.








Modifications Required (roll rear fender lips, adjustable camber parts for extra negative camber, hub-centric rings (66.6 mm), correct-length ball-seat lug bolts)















Modifications Required (roll rear fender lips, adjustable camber parts for extra negative camber, hub-centric rings (66.6 mm), correct-length ball-seat lug bolts)








The 1994-1995 Mercedes-Benz E-Class (W124) uses a 5X112 bolt pattern and a 66.6 mm center bore.
Factory sizes: 15x6.5 +44; 15x6.5 +48; 15x7 +41; 16x7 +46; 16x7.5 +42; 16x8 +34; 17x7 +46; 17x7.5 +42; 17x8.5 +34; 18x8 +42; 18x9 +30.
Its wheel fasteners use a M12x1.5 thread.
Bolt-on sizes run from 15" to 18" in diameter; see the size table for the offset range at each width.