Mazda MX-5 Miata (NC) 2007-2013 Wheel Fitment Guide

Bolt pattern, center bore, factory wheel sizes for each submodel and the aftermarket widths and offsets that bolt on to the Mazda MX-5 Miata built from 2007 to 2013 (SV, Sport, Touring, Club, Grand Touring).

Fitment specs

Bolt pattern5X114.3
Center bore67.1 mm
Lug threadM12x1.5
Model years2007-2013
GenerationNC

Every 2007-2013 Mazda MX-5 Miata uses a 5X114.3 bolt pattern with a 67.1 mm hub (center bore). Most aftermarket wheels are machined with a larger bore so one wheel can fit many cars; fit hub-centric rings with a 67.1 mm inner diameter so the wheel centers on the hub instead of the lugs. Lug thread is M12x1.5. Torque the lugs to the figure in your owner's manual and re-check them after the first 50 miles.

Years & submodels

US-market submodels of the Mazda MX-5 Miata (NC) and the model years each was sold. All of them share the 5X114.3 bolt pattern.

SubmodelYearsFactory wheel sizes
SV2007-200816x6.5 +55
Sport2007-201316x6.5 +55
Touring2007-201317x7 +55
Club201317x7 +55
Grand Touring2007-201317x7 +55

Factory wheel sizes

Wheel sizes Mazda fitted to the 2007-2013 Mazda MX-5 Miata from the factory (all submodels; the table above lists them by submodel). Offsets are ET in millimeters.

Factory size
16x6.5 +55
17x7 +55

Aftermarket sizes that bolt on

Widths and offsets with Verified Fitment on the 2007-2013 Mazda MX-5 Miata: no fender rolling, spacers or camber changes, and the wheel sits like the factory one or a little further out. Offsets outside a range below either rub, poke past the fender or sit tucked in. Test-fit one wheel for brake and suspension clearance before mounting tires.

SV, Sport

DiameterWidthOffset range
16-18"6.5"+31 to +60
16-18"7"+37 to +54
16-18"7.5"+43 to +48

Wider still: 16x8 +36 to +47; 17x8 +36 to +47; 18x8 +36 to +47 fit with modifications (roll front and rear fender lips, front camber bolts for -1°, hub-centric rings if the wheel bore is larger).

Touring, Club, Grand Touring

DiameterWidthOffset range
17-18"7"+37 to +55
17-18"7.5"+43 to +48

Wider still: 17x8 +36 to +47; 18x8 +36 to +47 fit with modifications (roll front and rear fender lips, front camber bolts for -1°, hub-centric rings if the wheel bore is larger).

Wheels in stock that fit

In-stock PG WHEELS sets in sizes with Verified Fitment for the 2007-2013 Mazda MX-5 Miata. Each card shows only the sizes that fit; prices are for a set of 4 with free shipping in the lower 48.

SV, Sport

Modifications Required (roll front and rear fender lips, front camber bolts for -1°, hub-centric rings if the wheel bore is larger)

Touring, Club, Grand Touring

Modifications Required (roll front and rear fender lips, front camber bolts for -1°, hub-centric rings if the wheel bore is larger)

FAQ

What is the bolt pattern of the 2007-2013 Mazda MX-5 Miata?

The 2007-2013 Mazda MX-5 Miata (NC) uses a 5X114.3 bolt pattern and a 67.1 mm center bore.

What size wheels came on the 2007-2013 Mazda MX-5 Miata from the factory?

Factory sizes: 16x6.5 +55; 17x7 +55.

What lug thread size does the 2007-2013 Mazda MX-5 Miata use?

Its wheel fasteners use a M12x1.5 thread.

What aftermarket wheel sizes fit the 2007-2013 Mazda MX-5 Miata without modifications?

Bolt-on sizes run from 16" to 18" in diameter; see the size table for the offset range at each width.