Bolt pattern, center bore, factory wheel sizes for each submodel and the aftermarket widths and offsets that bolt on to the Mercedes-Benz SL-Class built from 2002 to 2002 (SL500, SL600).
Every 2002 Mercedes-Benz SL-Class uses a 5X112 bolt pattern with a 66.6 mm hub (center bore). Most aftermarket wheels are machined with a larger bore so one wheel can fit many cars; fit hub-centric rings with a 66.6 mm inner diameter so the wheel centers on the hub instead of the lugs. Lug thread is M14x1.5. Torque the lugs to the figure in your owner's manual and re-check them after the first 50 miles.
US-market submodels of the Mercedes-Benz SL-Class (R129) and the model years each was sold. All of them share the 5X112 bolt pattern.
| Submodel | Years | Factory wheel sizes |
|---|---|---|
| SL500 | 2002 | 17x8.5 +35 18x8.5 +30 18x8.5 +35 18x8.5 +30 front / 18x9.5 +33 rear 18x8.5 +35 front / 18x9.5 +40 rear 19x8.5 +30 front / 19x9.5 +31 rear 19x8.5 +35 front / 19x9.5 +40 rear |
| SL600 | 2002 | 17x8.5 +34 18x8.5 +25 18x9.5 +23 19x10 +20 |
Wheel sizes Mercedes-Benz fitted to the 2002 Mercedes-Benz SL-Class from the factory (all submodels; the table above lists them by submodel). Offsets are ET in millimeters.
| Factory size |
|---|
| 17x8.5 +35 |
| 18x8.5 +30 |
| 18x8.5 +35 |
| 18x8.5 +30 front / 18x9.5 +33 rear |
| 18x8.5 +35 front / 18x9.5 +40 rear |
| 19x8.5 +30 front / 19x9.5 +31 rear |
| 19x8.5 +35 front / 19x9.5 +40 rear |
Widths and offsets with Verified Fitment on the 2002 Mercedes-Benz SL-Class: no fender rolling, spacers or camber changes, and the wheel sits like the factory one or a little further out. Offsets outside a range below either rub, poke past the fender or sit tucked in. Test-fit one wheel for brake and suspension clearance before mounting tires.
| Diameter | Width | Front offset | Rear offset |
|---|---|---|---|
| 18-19" | 8.5" | +13 to +35 | +3 to +45 |
| 18-19" | 9" | +19 to +29 | +9 to +45 |
| 18-19" | 9.5" | — | +16 to +38 |
| 18-19" | 10" | — | +22 to +32 |
Wider still: 18x11 front — / rear +14 to +25; 19x11 front — / rear +14 to +25 fit with modifications (roll rear fender lips, adjustable camber parts for extra negative camber, hub-centric rings (66.6 mm), correct-length ball-seat lug bolts).
| Diameter | Width | Front offset | Rear offset |
|---|---|---|---|
| 18-19" | 8.5" | +13 to +35 | +3 to +44 |
| 18-19" | 9" | +19 to +29 | +9 to +45 |
| 18-19" | 9.5" | — | +16 to +38 |
| 18-19" | 10" | — | +22 to +32 |
Wider still: 18x11 front — / rear +14 to +25; 19x11 front — / rear +14 to +25 fit with modifications (roll rear fender lips, adjustable camber parts for extra negative camber, hub-centric rings (66.6 mm), correct-length ball-seat lug bolts).
In-stock PG WHEELS sets in sizes with Verified Fitment for the 2002 Mercedes-Benz SL-Class. Each card shows only the sizes that fit; prices are for a set of 4 with free shipping in the lower 48.












Modifications Required (roll rear fender lips, adjustable camber parts for extra negative camber, hub-centric rings (66.6 mm), correct-length ball-seat lug bolts)














Modifications Required (roll rear fender lips, adjustable camber parts for extra negative camber, hub-centric rings (66.6 mm), correct-length ball-seat lug bolts)
The 2002 Mercedes-Benz SL-Class (R129) uses a 5X112 bolt pattern and a 66.6 mm center bore.
Factory sizes: 17x8.5 +35; 18x8.5 +30; 18x8.5 +35; 18x8.5 +30 front / 18x9.5 +33 rear; 18x8.5 +35 front / 18x9.5 +40 rear; 19x8.5 +30 front / 19x9.5 +31 rear; 19x8.5 +35 front / 19x9.5 +40 rear.
Its wheel fasteners use a M14x1.5 thread.
Bolt-on sizes run from 18" to 19" in diameter; see the size table for the offset range at each width.