Bolt pattern, center bore, factory wheel sizes for each submodel and the aftermarket widths and offsets that bolt on to the Mercedes-Benz SL-Class built from 2013 to 2020 (SL400, SL450, SL550, SL63 AMG, SL65 AMG).
Every 2013-2020 Mercedes-Benz SL-Class uses a 5X112 bolt pattern with a 66.6 mm hub (center bore). Most aftermarket wheels are machined with a larger bore so one wheel can fit many cars; fit hub-centric rings with a 66.6 mm inner diameter so the wheel centers on the hub instead of the lugs. Lug thread is M14x1.5. Torque the lugs to the figure in your owner's manual and re-check them after the first 50 miles.
US-market submodels of the Mercedes-Benz SL-Class (R231) and the model years each was sold. All of them share the 5X112 bolt pattern.
| Submodel | Years | Factory wheel sizes |
|---|---|---|
| SL400 | 2016 | 18x8.5 +35.5 front / 18x9.5 +47.5 rear 19x8.5 +34.5 front / 19x9.5 +48 rear 19x9 +27 front / 20x10 +48 rear |
| SL450 | 2017-2020 | 19x8.5 +34.5 front / 19x9.5 +48 rear 19x9 +27 front / 20x10 +48 rear |
| SL550 | 2013-2020 | 18x8.5 +35.5 front / 18x9.5 +47.5 rear 19x8.5 +34.5 front / 19x9.5 +48 rear 19x9 +27 front / 20x10 +48 rear |
| SL63 AMG | 2013-2019 | See factory sizes below |
| SL65 AMG | 2014-2018 | See factory sizes below |
Wheel sizes Mercedes-Benz fitted to the 2013-2020 Mercedes-Benz SL-Class from the factory (all submodels; the table above lists them by submodel). Offsets are ET in millimeters.
| Factory size |
|---|
| 18x8.5 +35.5 front / 18x9.5 +47.5 rear |
| 19x8.5 +34.5 front / 19x9.5 +48 rear |
| 19x9 +27 front / 20x10 +48 rear |
Widths and offsets with Verified Fitment on the 2013-2020 Mercedes-Benz SL-Class: no fender rolling, spacers or camber changes, and the wheel sits like the factory one or a little further out. Offsets outside a range below either rub, poke past the fender or sit tucked in. Test-fit one wheel for brake and suspension clearance before mounting tires.
| Diameter | Width | Front offset | Rear offset |
|---|---|---|---|
| 18-21" | 8.5" | +18 to +41 | — |
| 18-21" | 9" | +25 to +35 | — |
| 18-21" | 9.5" | — | +30 to +53 |
| 18-21" | 10" | — | +37 to +47 |
Wider still: 18x11 front — / rear +29 to +40; 19x11 front — / rear +29 to +40; 20x11 front — / rear +29 to +40; 21x11 front — / rear +29 to +40 fit with modifications (roll rear fender lips, adjustable camber parts for extra negative camber, hub-centric rings (66.6 mm), correct-length ball-seat lug bolts).
| Diameter | Width | Front offset | Rear offset |
|---|---|---|---|
| 19-21" | 8.5" | +18 to +41 | — |
| 19-21" | 9" | +25 to +35 | — |
| 19-21" | 9.5" | — | +30 to +53 |
| 19-21" | 10" | — | +37 to +47 |
Wider still: 19x11 front — / rear +29 to +40; 20x11 front — / rear +29 to +40; 21x11 front — / rear +29 to +40 fit with modifications (roll rear fender lips, adjustable camber parts for extra negative camber, hub-centric rings (66.6 mm), correct-length ball-seat lug bolts).
In-stock PG WHEELS sets in sizes with Verified Fitment for the 2013-2020 Mercedes-Benz SL-Class. Each card shows only the sizes that fit; prices are for a set of 4 with free shipping in the lower 48.












Modifications Required (roll rear fender lips, adjustable camber parts for extra negative camber, hub-centric rings (66.6 mm), correct-length ball-seat lug bolts)














Modifications Required (roll rear fender lips, adjustable camber parts for extra negative camber, hub-centric rings (66.6 mm), correct-length ball-seat lug bolts)
The 2013-2020 Mercedes-Benz SL-Class (R231) uses a 5X112 bolt pattern and a 66.6 mm center bore.
Factory sizes: 18x8.5 +35.5 front / 18x9.5 +47.5 rear; 19x8.5 +34.5 front / 19x9.5 +48 rear; 19x9 +27 front / 20x10 +48 rear.
Its wheel fasteners use a M14x1.5 thread.
Bolt-on sizes run from 18" to 21" in diameter; see the size table for the offset range at each width.