BMW 7 Series (E38) 1995-2001 Wheel Fitment Guide

Bolt pattern, center bore, factory wheel sizes for each submodel and the aftermarket widths and offsets that bolt on to the BMW 7 Series built from 1995 to 2001 (740i, 740iL, 750iL).

Fitment specs

Bolt pattern5X120
Center bore72.6 mm
Lug threadM12x1.5
Model years1995-2001
GenerationE38

Every 1995-2001 BMW 7 Series uses a 5X120 bolt pattern with a 72.6 mm hub (center bore). Most aftermarket wheels are machined with a larger bore so one wheel can fit many cars; fit hub-centric rings with a 72.6 mm inner diameter so the wheel centers on the hub instead of the lugs. Lug thread is M12x1.5. Torque the lugs to the figure in your owner's manual and re-check them after the first 50 miles.

Years & submodels

US-market submodels of the BMW 7 Series (E38) and the model years each was sold. All of them share the 5X120 bolt pattern.

SubmodelYearsFactory wheel sizes
740i1995-200116x7.5 +20
17x8 +23
18x8 +13 front / 18x9.5 +25 rear
740iL1995-200116x7.5 +20
17x8 +23
18x8 +13 front / 18x9.5 +25 rear
750iL1995-200116x7.5 +20
17x8 +23
18x9.5 +25

Factory wheel sizes

Wheel sizes BMW fitted to the 1995-2001 BMW 7 Series from the factory (all submodels; the table above lists them by submodel). Offsets are ET in millimeters.

Factory size
16x7.5 +20
17x8 +23
18x8 +13 front / 18x9.5 +25 rear
18x9.5 +25

Aftermarket sizes that bolt on

Widths and offsets with Verified Fitment on the 1995-2001 BMW 7 Series: no fender rolling, spacers or camber changes, and the wheel sits like the factory one or a little further out. Offsets outside a range below either rub, poke past the fender or sit tucked in. Test-fit one wheel for brake and suspension clearance before mounting tires.

DiameterWidthFront offsetRear offset
16-18"7.5"-10 to +25+3 to +25
19"7.5"-10 to +25—
16-18"8"-4 to +19+9 to +19
19"8"-4 to +19—
16-19"8.5"+2 to +13—

Wider still: 16x9.5 front -6 to +6 / rear —; 17x9.5 front -6 to +6 / rear —; 18x9.5 front -6 to +6 / rear —; 19x9.5 front -6 to +6 / rear — fit with modifications (roll rear fender lips, adjustable rear camber arms for -1.5° or more, front camber plates, hub-centric rings if wheel bore is larger than the hub).

FAQ

What is the bolt pattern of the 1995-2001 BMW 7 Series?

The 1995-2001 BMW 7 Series (E38) uses a 5X120 bolt pattern and a 72.6 mm center bore.

What size wheels came on the 1995-2001 BMW 7 Series from the factory?

Factory sizes: 16x7.5 +20; 17x8 +23; 18x8 +13 front / 18x9.5 +25 rear; 18x9.5 +25.

What lug thread size does the 1995-2001 BMW 7 Series use?

Its wheel fasteners use a M12x1.5 thread.

What aftermarket wheel sizes fit the 1995-2001 BMW 7 Series without modifications?

Bolt-on sizes run from 16" to 19" in diameter; see the size table for the offset range at each width.