Bolt pattern, center bore, factory wheel sizes for each submodel and the aftermarket widths and offsets that bolt on to the BMW 7 Series built from 2009 to 2015 (740i, 740Li, 740Li xDrive, 740Ld xDrive, 750i, 750Li, 750i xDrive, 750Li xDrive, ActiveHybrid 7, 760Li).
Every 2009-2015 BMW 7 Series uses a 5X120 bolt pattern with a 72.6 mm hub (center bore). Most aftermarket wheels are machined with a larger bore so one wheel can fit many cars; fit hub-centric rings with a 72.6 mm inner diameter so the wheel centers on the hub instead of the lugs. Lug thread is M14x1.25. Torque the lugs to the figure in your owner's manual and re-check them after the first 50 miles.
US-market submodels of the BMW 7 Series (F01/F02) and the model years each was sold. All of them share the 5X120 bolt pattern.
| Submodel | Years | Factory wheel sizes |
|---|---|---|
| 740i | 2011-2015 | 18x8 +30 19x8.5 +25 19x8.5 +25 front / 19x9.5 +39 rear 19x9.5 +39 20x8.5 +25 front / 20x10 +41 rear 20x10 +41 21x8.5 +25 front / 21x10 +41 rear 21x10 +41 |
| 740Li | 2011-2015 | 18x8 +30 19x8.5 +25 19x8.5 +25 front / 19x9.5 +39 rear 20x8.5 +25 front / 20x10 +41 rear 21x8.5 +25 front / 21x10 +41 rear |
| 740Li xDrive | 2013-2015 | 18x8 +30 19x8.5 +25 19x8.5 +25 front / 19x9.5 +39 rear 20x8.5 +25 front / 20x10 +41 rear 21x8.5 +25 front / 21x10 +41 rear |
| 740Ld xDrive | 2014-2015 | 18x8 +30 19x8.5 +25 19x8.5 +25 front / 19x9.5 +39 rear 20x8.5 +25 front / 20x10 +41 rear 21x8.5 +25 front / 21x10 +41 rear |
| 750i | 2009-2015 | 18x8 +30 19x8.5 +25 19x9.5 +39 20x10 +41 21x10 +41 |
| 750Li | 2009-2015 | 18x8 +30 19x8.5 +25 19x8.5 +25 front / 19x9.5 +39 rear 19x9.5 +39 20x8.5 +25 front / 20x10 +41 rear 20x10 +41 21x8.5 +25 front / 21x10 +41 rear 21x10 +41 |
| 750i xDrive | 2011-2015 | 18x8 +30 19x8.5 +25 19x9.5 +39 20x10 +41 21x10 +41 |
| 750Li xDrive | 2011-2015 | 18x8 +30 19x8.5 +25 19x9.5 +39 20x10 +41 21x10 +41 |
| ActiveHybrid 7 | 2011-2015 | 18x8 +30 19x8.5 +25 19x9.5 +39 20x10 +41 21x10 +41 |
| 760Li | 2010-2015 | 18x8 +30 19x8.5 +25 19x9.5 +39 20x10 +41 21x10 +41 |
Wheel sizes BMW fitted to the 2009-2015 BMW 7 Series from the factory (all submodels; the table above lists them by submodel). Offsets are ET in millimeters.
| Factory size |
|---|
| 18x8 +30 |
| 19x8.5 +25 |
| 19x8.5 +25 front / 19x9.5 +39 rear |
| 19x9.5 +39 |
| 20x8.5 +25 front / 20x10 +41 rear |
| 20x10 +41 |
| 21x8.5 +25 front / 21x10 +41 rear |
| 21x10 +41 |
Widths and offsets with Verified Fitment on the 2009-2015 BMW 7 Series: no fender rolling, spacers or camber changes, and the wheel sits like the factory one or a little further out. Offsets outside a range below either rub, poke past the fender or sit tucked in. Test-fit one wheel for brake and suspension clearance before mounting tires.
| Diameter | Width | Front offset | Rear offset |
|---|---|---|---|
| 18-21" | 8" | +1 to +40 | +3 to +40 |
| 18-21" | 8.5" | +8 to +46 | +9 to +46 |
| 18-21" | 9" | +14 to +51 | +15 to +51 |
| 18-21" | 9.5" | +21 to +44 | +22 to +44 |
| 18-21" | 10" | +27 to +38 | +28 to +38 |
Wider still: 18x11 front +19 to +31 / rear +20 to +31; 18x11.5 front +25 / rear —; 19x11 front +19 to +31 / rear +20 to +31; 19x11.5 front +25 / rear —; 20x11 front +19 to +31 / rear +20 to +31; 20x11.5 front +25 / rear —… fit with modifications (roll rear fender lips, adjustable rear camber arms for -1.5° or more, front camber plates, hub-centric rings if wheel bore is larger than the hub).
In-stock PG WHEELS sets in sizes with Verified Fitment for the 2009-2015 BMW 7 Series. Each card shows only the sizes that fit; prices are for a set of 4 with free shipping in the lower 48.












Modifications Required (roll rear fender lips, adjustable rear camber arms for -1.5° or more, front camber plates, hub-centric rings if wheel bore is larger than the hub)
The 2009-2015 BMW 7 Series (F01/F02) uses a 5X120 bolt pattern and a 72.6 mm center bore.
Factory sizes: 18x8 +30; 19x8.5 +25; 19x8.5 +25 front / 19x9.5 +39 rear; 19x9.5 +39; 20x8.5 +25 front / 20x10 +41 rear; 20x10 +41; 21x8.5 +25 front / 21x10 +41 rear; 21x10 +41.
Its wheel fasteners use a M14x1.25 thread.
Bolt-on sizes run from 18" to 21" in diameter; see the size table for the offset range at each width.