Bolt pattern, center bore, factory wheel sizes for each submodel and the aftermarket widths and offsets that bolt on to the BMW 7 Series built from 2002 to 2008 (745i, 745Li, 750i, 750Li, 760Li, ALPINA B7).
Every 2002-2008 BMW 7 Series uses a 5X120 bolt pattern with a 72.6 mm hub (center bore). Most aftermarket wheels are machined with a larger bore so one wheel can fit many cars; fit hub-centric rings with a 72.6 mm inner diameter so the wheel centers on the hub instead of the lugs. Lug thread is M14x1.5. Torque the lugs to the figure in your owner's manual and re-check them after the first 50 miles.
US-market submodels of the BMW 7 Series (E65/E66) and the model years each was sold. All of them share the 5X120 bolt pattern.
| Submodel | Years | Factory wheel sizes |
|---|---|---|
| 745i | 2002-2005 | 17x8 +24 18x8 +24 19x9 +24 front / 19x10 +24 rear 20x9 +24 front / 20x10 +24 rear |
| 745Li | 2002-2005 | 17x8 +24 18x8 +24 19x9 +24 front / 19x10 +24 rear 20x9 +24 front / 20x10 +24 rear |
| 750i | 2006-2008 | 17x8 +24 18x8 +24 19x9 +24 front / 19x10 +24 rear 20x9 +24 front / 20x10 +24 rear 21x9 +22 front / 21x10 +32 rear |
| 750Li | 2006-2008 | 17x8 +24 18x8 +24 19x9 +24 front / 19x10 +24 rear 20x9 +24 front / 20x10 +24 rear 21x9 +22 front / 21x10 +32 rear |
| 760Li | 2004-2008 | 18x8 +24 19x10 +24 20x10 +24 21x10 +32 |
| ALPINA B7 | 2007-2008 | See factory sizes below |
Wheel sizes BMW fitted to the 2002-2008 BMW 7 Series from the factory (all submodels; the table above lists them by submodel). Offsets are ET in millimeters.
| Factory size |
|---|
| 17x8 +24 |
| 18x8 +24 |
| 19x9 +24 front / 19x10 +24 rear |
| 19x10 +24 |
| 20x9 +24 front / 20x10 +24 rear |
| 20x10 +24 |
| 21x9 +22 front / 21x10 +32 rear |
| 21x10 +32 |
Widths and offsets with Verified Fitment on the 2002-2008 BMW 7 Series: no fender rolling, spacers or camber changes, and the wheel sits like the factory one or a little further out. Offsets outside a range below either rub, poke past the fender or sit tucked in. Test-fit one wheel for brake and suspension clearance before mounting tires.
| Diameter | Width | Front offset | Rear offset |
|---|---|---|---|
| 19-21" | 8" | -19 to +34 | — |
| 19-21" | 8.5" | -12 to +40 | — |
| 19-21" | 9" | -6 to +42 | -6 to +42 |
| 19-21" | 9.5" | +0 to +36 | +0 to +36 |
| 19-21" | 10" | +7 to +29 | +7 to +29 |
| 19-21" | 10.5" | +13 to +23 | +13 to +23 |
Wider still: 19x11.5 front +5 to +16 / rear +5 to +16; 20x11.5 front +5 to +16 / rear +5 to +16; 21x11.5 front +5 to +16 / rear +5 to +16 fit with modifications (roll rear fender lips, adjustable rear camber arms for -1.5° or more, front camber plates, hub-centric rings if wheel bore is larger than the hub).
| Diameter | Width | Front offset | Rear offset |
|---|---|---|---|
| 19-21" | 8" | -19 to +34 | — |
| 19-21" | 8.5" | -12 to +40 | — |
| 19-21" | 9" | -6 to +42 | -6 to +42 |
| 19-21" | 9.5" | +0 to +36 | +0 to +36 |
| 19-21" | 10" | +7 to +29 | +7 to +29 |
| 19-21" | 10.5" | +13 to +23 | +13 to +23 |
Wider still: 19x11.5 front +5 to +16 / rear +5 to +16; 20x11.5 front +5 to +16 / rear +5 to +16; 21x11.5 front +5 to +16 / rear +5 to +16 fit with modifications (roll rear fender lips, adjustable rear camber arms for -1.5° or more, front camber plates, hub-centric rings if wheel bore is larger than the hub).
| Diameter | Width | Front offset | Rear offset |
|---|---|---|---|
| 19-21" | 9" | -6 to +34 | — |
| 19-21" | 9.5" | +0 to +36 | — |
| 19-21" | 10" | +7 to +29 | +7 to +29 |
| 19-21" | 10.5" | +13 to +23 | +13 to +23 |
Wider still: 19x11.5 front +5 to +16 / rear +5 to +16; 20x11.5 front +5 to +16 / rear +5 to +16; 21x11.5 front +5 to +16 / rear +5 to +16 fit with modifications (roll rear fender lips, adjustable rear camber arms for -1.5° or more, front camber plates, hub-centric rings if wheel bore is larger than the hub).
In-stock PG WHEELS sets in sizes with Verified Fitment for the 2002-2008 BMW 7 Series. Each card shows only the sizes that fit; prices are for a set of 4 with free shipping in the lower 48.






Modifications Required (roll rear fender lips, adjustable rear camber arms for -1.5° or more, front camber plates, hub-centric rings if wheel bore is larger than the hub)











Modifications Required (roll rear fender lips, adjustable rear camber arms for -1.5° or more, front camber plates, hub-centric rings if wheel bore is larger than the hub)





Modifications Required (roll rear fender lips, adjustable rear camber arms for -1.5° or more, front camber plates, hub-centric rings if wheel bore is larger than the hub)







The 2002-2008 BMW 7 Series (E65/E66) uses a 5X120 bolt pattern and a 72.6 mm center bore.
Factory sizes: 17x8 +24; 18x8 +24; 19x9 +24 front / 19x10 +24 rear; 19x10 +24; 20x9 +24 front / 20x10 +24 rear; 20x10 +24; 21x9 +22 front / 21x10 +32 rear; 21x10 +32.
Its wheel fasteners use a M14x1.5 thread.
Bolt-on sizes run from 19" to 21" in diameter; see the size table for the offset range at each width.