Bolt pattern, center bore, factory wheel sizes for each submodel and the aftermarket widths and offsets that bolt on to the Porsche 911 built from 1995 to 1998 (Carrera, Carrera Cabriolet, Carrera 4, Targa, Carrera 4S, Carrera S, Turbo, Turbo S).
Every 1995-1998 Porsche 911 uses a 5X130 bolt pattern with a 71.6 mm hub (center bore). Most aftermarket wheels are machined with a larger bore so one wheel can fit many cars; fit hub-centric rings with a 71.6 mm inner diameter so the wheel centers on the hub instead of the lugs. Lug thread is M14x1.5. Torque the lugs to the figure in your owner's manual and re-check them after the first 50 miles.
US-market submodels of the Porsche 911 (993) and the model years each was sold. All of them share the 5X130 bolt pattern.
| Submodel | Years | Factory wheel sizes |
|---|---|---|
| Carrera | 1995-1998 | See factory sizes below |
| Carrera Cabriolet | 1995-1998 | See factory sizes below |
| Carrera 4 | 1995-1998 | See factory sizes below |
| Targa | 1996-1998 | See factory sizes below |
| Carrera 4S | 1996-1998 | 18x8 +52 front / 18x10 +40 rear 18x8 +52 front / 18x10 +65 rear 18x10 +40 18x10 +65 |
| Carrera S | 1998 | See factory sizes below |
| Turbo | 1996-1997 | 18x8 +52 front / 18x10 +40 rear 18x8 +52 front / 18x10 +65 rear 18x10 +40 18x10 +65 |
| Turbo S | 1997 | 18x8 +52 front / 18x10 +40 rear 18x8 +52 front / 18x10 +65 rear 18x10 +40 18x10 +65 |
Wheel sizes Porsche fitted to the 1995-1998 Porsche 911 from the factory (all submodels; the table above lists them by submodel). Offsets are ET in millimeters.
| Factory size |
|---|
| 16x7 +55 front / 16x8 +70 rear |
| 16x7 +55 front / 16x9 +70 rear |
| 16x8 +70 |
| 16x9 +70 |
| 17x7 +55 front / 17x8 +70 rear |
| 17x7 +55 front / 17x8 +30 rear |
| 17x7 +55 front / 17x9 +55 rear |
| 17x8 +30 |
| 17x8 +70 |
| 17x9 +55 |
| 18x8 +52 front / 18x10 +65 rear |
| 18x8 +52 front / 18x10 +40 rear |
| 18x10 +40 |
| 18x10 +65 |
| 19x8 +50 front / 19x11 +30 rear |
| 19x11 +30 |
Widths and offsets with Verified Fitment on the 1995-1998 Porsche 911: no fender rolling, spacers or camber changes, and the wheel sits like the factory one or a little further out. Offsets outside a range below either rub, poke past the fender or sit tucked in. Test-fit one wheel for brake and suspension clearance before mounting tires.
| Diameter | Width | Front offset | Rear offset |
|---|---|---|---|
| 16-18" | 7" | +0 to +65 | — |
| 16-18" | 7.5" | +7 to +71 | — |
| 16-18" | 8" | +13 to +75 | +13 to +75 |
| 16-18" | 8.5" | +19 to +69 | +19 to +69 |
| 16-18" | 9" | +26 to +63 | +26 to +63 |
Wider still: 16x9.5 front +11 to +62 / rear +11 to +62; 16x10 front +18 to +56 / rear +18 to +56; 17x9.5 front +11 to +62 / rear +11 to +62; 17x10 front +18 to +56 / rear +18 to +56; 18x9.5 front +11 to +62 / rear +11 to +62; 18x10 front +18 to +56 / rear +18 to +56 fit with modifications (roll rear fender lips, longer wheel studs when running spacers, camber adjustment at strut top / rear spring plate).
| Diameter | Width | Front offset | Rear offset |
|---|---|---|---|
| 18" | 8" | +13 to +62 | — |
| 18" | 8.5" | +19 to +68 | — |
| 18" | 9" | +26 to +63 | — |
| 18" | 10" | — | +38 to +50 |
The 1995-1998 Porsche 911 (993) uses a 5X130 bolt pattern and a 71.6 mm center bore.
Factory sizes: 16x7 +55 front / 16x8 +70 rear; 16x7 +55 front / 16x9 +70 rear; 16x8 +70; 16x9 +70; 17x7 +55 front / 17x8 +70 rear; 17x7 +55 front / 17x8 +30 rear; 17x7 +55 front / 17x9 +55 rear; 17x8 +30; 17x8 +70; 17x9 +55; 18x8 +52 front / 18x10 +65 rear; 18x8 +52 front / 18x10 +40 rear; 18x10 +40; 18x10 +65; 19x8 +50 front / 19x11 +30 rear; 19x11 +30.
Its wheel fasteners use a M14x1.5 thread.
Bolt-on sizes run from 16" to 18" in diameter; see the size table for the offset range at each width.