Bolt pattern, center bore, factory wheel sizes for each submodel and the aftermarket widths and offsets that bolt on to the Mercedes-Benz S-Class built from 1992 to 1998 (300SD, 300SE, 400SE, 400SEL, 500SEL, 600SEL, S320, S350, S420, S500, S600).
Every 1992-1998 Mercedes-Benz S-Class uses a 5X112 bolt pattern with a 66.6 mm hub (center bore). Most aftermarket wheels are machined with a larger bore so one wheel can fit many cars; fit hub-centric rings with a 66.6 mm inner diameter so the wheel centers on the hub instead of the lugs. Lug thread is M14x1.5. Torque the lugs to the figure in your owner's manual and re-check them after the first 50 miles.
US-market submodels of the Mercedes-Benz S-Class (W140) and the model years each was sold. All of them share the 5X112 bolt pattern.
| Submodel | Years | Factory wheel sizes |
|---|---|---|
| 300SD | 1992-1993 | 16x7.5 +51 |
| 300SE | 1992-1993 | 16x7.5 +51 |
| 400SE | 1992-1993 | 16x7.5 +51 |
| 400SEL | 1993 | 16x7.5 +51 |
| 500SEL | 1992-1993 | 16x7.5 +51 |
| 600SEL | 1992-1993 | 16x7.5 +51 |
| S320 | 1994-1998 | 16x7.5 +46 16x7.5 +51 17x7.5 +46 17x7.5 +51 18x8 +44 18x8 +44 front / 18x9 +44 rear 18x8.5 +44 18x8.5 +44 front / 18x9.5 +46 rear |
| S350 | 1994-1995 | 16x7.5 +51 |
| S420 | 1994-1998 | 16x7.5 +51 |
| S500 | 1994-1998 | 17x7.5 +46 17x7.5 +51 18x8 +44 18x8.5 +44 18x9 +46 18x9.5 +46 19x8.5 +40 |
| S600 | 1994-1998 | 18x8 +44 18x8.5 +44 18x9 +46 18x9.5 +46 19x10 +45 |
Wheel sizes Mercedes-Benz fitted to the 1992-1998 Mercedes-Benz S-Class from the factory (all submodels; the table above lists them by submodel). Offsets are ET in millimeters.
| Factory size |
|---|
| 16x7.5 +51 |
| 17x8 +50 |
| 18x7.5 +51 front / 18x8.5 +47 rear |
| 18x8 +50 |
| 18x8 +50 front / 18x8.5 +47 rear |
| 18x8.5 +47 |
Widths and offsets with Verified Fitment on the 1992-1998 Mercedes-Benz S-Class: no fender rolling, spacers or camber changes, and the wheel sits like the factory one or a little further out. Offsets outside a range below either rub, poke past the fender or sit tucked in. Test-fit one wheel for brake and suspension clearance before mounting tires.
| Diameter | Width | Offset range |
|---|---|---|
| 16-19" | 7.5" | +34 to +56 |
| 16-19" | 8" | +40 to +50 |
Wider still: 16x9 +32 to +43; 17x9 +32 to +43; 18x9 +32 to +43; 19x9 +32 to +43 fit with modifications (roll rear fender lips, adjustable camber parts for extra negative camber, hub-centric rings (66.6 mm), correct-length ball-seat lug bolts).
| Diameter | Width | Offset range |
|---|---|---|
| 16-19" | 7.5" | +34 to +56 |
| 16-19" | 8" | +40 to +50 |
Wider still: 16x9 +32 to +43; 17x9 +32 to +43; 18x9 +32 to +43; 19x9 +32 to +43 fit with modifications (roll rear fender lips, adjustable camber parts for extra negative camber, hub-centric rings (66.6 mm), correct-length ball-seat lug bolts).
| Diameter | Width | Offset range |
|---|---|---|
| 17-19" | 7.5" | +34 to +56 |
| 17-19" | 8" | +40 to +50 |
Wider still: 17x9 +32 to +43; 18x9 +32 to +43; 19x9 +32 to +43 fit with modifications (roll rear fender lips, adjustable camber parts for extra negative camber, hub-centric rings (66.6 mm), correct-length ball-seat lug bolts).
| Diameter | Width | Offset range |
|---|---|---|
| 18-19" | 8" | +40 to +50 |
Wider still: 18x9 +32 to +43; 19x9 +32 to +43 fit with modifications (roll rear fender lips, adjustable camber parts for extra negative camber, hub-centric rings (66.6 mm), correct-length ball-seat lug bolts).
In-stock PG WHEELS sets in sizes with Verified Fitment for the 1992-1998 Mercedes-Benz S-Class. Each card shows only the sizes that fit; prices are for a set of 4 with free shipping in the lower 48.
Modifications Required (roll rear fender lips, adjustable camber parts for extra negative camber, hub-centric rings (66.6 mm), correct-length ball-seat lug bolts)












Modifications Required (roll rear fender lips, adjustable camber parts for extra negative camber, hub-centric rings (66.6 mm), correct-length ball-seat lug bolts)












Modifications Required (roll rear fender lips, adjustable camber parts for extra negative camber, hub-centric rings (66.6 mm), correct-length ball-seat lug bolts)












Modifications Required (roll rear fender lips, adjustable camber parts for extra negative camber, hub-centric rings (66.6 mm), correct-length ball-seat lug bolts)












The 1992-1998 Mercedes-Benz S-Class (W140) uses a 5X112 bolt pattern and a 66.6 mm center bore.
Factory sizes: 16x7.5 +51; 17x8 +50; 18x7.5 +51 front / 18x8.5 +47 rear; 18x8 +50; 18x8 +50 front / 18x8.5 +47 rear; 18x8.5 +47.
Its wheel fasteners use a M14x1.5 thread.
Bolt-on sizes run from 16" to 19" in diameter; see the size table for the offset range at each width.