Bolt pattern, center bore, factory wheel sizes for each submodel and the aftermarket widths and offsets that bolt on to the Mercedes-Benz S-Class built from 2007 to 2013 (S550, S550 4MATIC, S400 Hybrid, S350 BlueTEC 4MATIC, S600, S63 AMG, S65 AMG).
Every 2007-2013 Mercedes-Benz S-Class uses a 5X112 bolt pattern with a 66.6 mm hub (center bore). Most aftermarket wheels are machined with a larger bore so one wheel can fit many cars; fit hub-centric rings with a 66.6 mm inner diameter so the wheel centers on the hub instead of the lugs. Torque the lugs to the figure in your owner's manual and re-check them after the first 50 miles.
US-market submodels of the Mercedes-Benz S-Class (W221) and the model years each was sold. All of them share the 5X112 bolt pattern.
| Submodel | Years | Factory wheel sizes |
|---|---|---|
| S550 | 2007-2013 | 18x8.5 +43 18x8.5 +43 front / 18x9.5 +43 rear 18x9.5 +43 19x8.5 +43 front / 19x9.5 +43 rear 19x9.5 +43 20x8.5 +43 front / 20x9.5 +43 rear 20x9.5 +43 |
| S550 4MATIC | 2008-2013 | See factory sizes below |
| S400 Hybrid | 2010-2013 | See factory sizes below |
| S350 BlueTEC 4MATIC | 2012-2013 | See factory sizes below |
| S600 | 2007-2013 | 18x8.5 +43 18x8.5 +43 front / 18x9.5 +43 rear 18x9.5 +43 19x8.5 +43 front / 19x9.5 +43 rear 19x9.5 +43 20x8.5 +43 front / 20x9.5 +43 rear 20x9 +40 front / 20x10 +40 rear 20x9.5 +43 20x10 +40 |
| S63 AMG | 2008-2013 | See factory sizes below |
| S65 AMG | 2007-2013 | See factory sizes below |
Wheel sizes Mercedes-Benz fitted to the 2007-2013 Mercedes-Benz S-Class from the factory (all submodels; the table above lists them by submodel). Offsets are ET in millimeters.
| Factory size |
|---|
| 18x8.5 +43 |
| 18x8.5 +43 front / 18x9.5 +43 rear |
| 18x9.5 +43 |
| 19x8.5 +43 front / 19x9.5 +43 rear |
| 19x9.5 +43 |
| 20x8.5 +43 front / 20x9.5 +43 rear |
| 20x9 +40 front / 20x10 +40 rear |
| 20x9.5 +43 |
| 20x10 +40 |
Widths and offsets with Verified Fitment on the 2007-2013 Mercedes-Benz S-Class: no fender rolling, spacers or camber changes, and the wheel sits like the factory one or a little further out. Offsets outside a range below either rub, poke past the fender or sit tucked in. Test-fit one wheel for brake and suspension clearance before mounting tires.
| Diameter | Width | Offset range |
|---|---|---|
| 18-20" | 8.5" | +13 to +53 |
| 18-20" | 9" | +19 to +55 |
| 18-20" | 9.5" | +26 to +48 |
| 18-20" | 10" | +32 to +42 |
Wider still: 18x11 +24 to +35; 19x11 +24 to +35; 20x11 +24 to +35 fit with modifications (roll rear fender lips, adjustable camber parts for extra negative camber, hub-centric rings (66.6 mm), correct-length ball-seat lug bolts).
| Diameter | Width | Offset range |
|---|---|---|
| 18-19" | 8.5" | +13 to +53 |
| 18-19" | 9" | +19 to +55 |
| 18-19" | 9.5" | +26 to +48 |
| 18-19" | 10" | +32 to +42 |
Wider still: 18x11 +24 to +35; 19x11 +24 to +35 fit with modifications (roll rear fender lips, adjustable camber parts for extra negative camber, hub-centric rings (66.6 mm), correct-length ball-seat lug bolts).
In-stock PG WHEELS sets in sizes with Verified Fitment for the 2007-2013 Mercedes-Benz S-Class. Each card shows only the sizes that fit; prices are for a set of 4 with free shipping in the lower 48.












Modifications Required (roll rear fender lips, adjustable camber parts for extra negative camber, hub-centric rings (66.6 mm), correct-length ball-seat lug bolts)














Modifications Required (roll rear fender lips, adjustable camber parts for extra negative camber, hub-centric rings (66.6 mm), correct-length ball-seat lug bolts)
The 2007-2013 Mercedes-Benz S-Class (W221) uses a 5X112 bolt pattern and a 66.6 mm center bore.
Factory sizes: 18x8.5 +43; 18x8.5 +43 front / 18x9.5 +43 rear; 18x9.5 +43; 19x8.5 +43 front / 19x9.5 +43 rear; 19x9.5 +43; 20x8.5 +43 front / 20x9.5 +43 rear; 20x9 +40 front / 20x10 +40 rear; 20x9.5 +43; 20x10 +40.
Bolt-on sizes run from 18" to 20" in diameter; see the size table for the offset range at each width.