Bolt pattern, center bore, factory wheel sizes for each submodel and the aftermarket widths and offsets that bolt on to the Mercedes-Benz S-Class built from 1981 to 1991 (300 SD, 300 SDL, 300 SE, 350 SDL, 380 SE, 380 SEC, 380 SEL, 420 SEL).
Every 1981-1991 Mercedes-Benz S-Class uses a 5X112 bolt pattern with a 66.6 mm hub (center bore). Most aftermarket wheels are machined with a larger bore so one wheel can fit many cars; fit hub-centric rings with a 66.6 mm inner diameter so the wheel centers on the hub instead of the lugs. Lug thread is M12x1.5. Torque the lugs to the figure in your owner's manual and re-check them after the first 50 miles.
US-market submodels of the Mercedes-Benz S-Class (W126) and the model years each was sold. All of them share the 5X112 bolt pattern.
| Submodel | Years | Factory wheel sizes |
|---|---|---|
| 300 SD | 1981-1991 | 15x7 +25 16x7 +25 16x7.5 +20 |
| 300 SDL | 1981-1991 | 15x7 +25 16x7 +25 16x7.5 +20 |
| 300 SE | 1981-1991 | 15x7 +25 16x7 +25 16x7.5 +20 |
| 350 SDL | 1981-1991 | 15x7 +25 16x7 +25 16x7.5 +20 |
| 380 SE | 1981-1991 | 14x6.5 +30 15x7 +25 16x7.5 +20 |
| 380 SEC | 1981-1991 | 14x6.5 +30 15x7 +25 16x7.5 +20 |
| 380 SEL | 1981-1991 | 14x6.5 +30 15x7 +25 16x7.5 +20 |
| 420 SEL | 1981-1991 | 15x7 +25 16x7.5 +25 16x8 +20 |
Wheel sizes Mercedes-Benz fitted to the 1981-1991 Mercedes-Benz S-Class from the factory (all submodels; the table above lists them by submodel). Offsets are ET in millimeters.
| Factory size |
|---|
| 14x6.5 +30 |
| 15x7 +25 |
| 16x7 +25 |
| 16x7.5 +20 |
| 16x7.5 +25 |
| 16x8 +20 |
| 17x8.5 +20 |
Widths and offsets with Verified Fitment on the 1981-1991 Mercedes-Benz S-Class: no fender rolling, spacers or camber changes, and the wheel sits like the factory one or a little further out. Offsets outside a range below either rub, poke past the fender or sit tucked in. Test-fit one wheel for brake and suspension clearance before mounting tires.
| Diameter | Width | Offset range |
|---|---|---|
| 15-18" | 7" | +8 to +31 |
| 15-18" | 7.5" | +14 to +24 |
Wider still: 15x8.5 +6 to +17; 16x8.5 +6 to +17; 17x8.5 +6 to +17; 18x8.5 +6 to +17 fit with modifications (roll rear fender lips, adjustable camber parts for extra negative camber, hub-centric rings (66.6 mm), correct-length ball-seat lug bolts).
| Diameter | Width | Offset range |
|---|---|---|
| 14-18" | 6.5" | +2 to +37 |
| 14-18" | 7" | +8 to +31 |
| 14-18" | 7.5" | +14 to +24 |
Wider still: 14x8.5 +6 to +17; 15x8.5 +6 to +17; 16x8.5 +6 to +17; 17x8.5 +6 to +17; 18x8.5 +6 to +17 fit with modifications (roll rear fender lips, adjustable camber parts for extra negative camber, hub-centric rings (66.6 mm), correct-length ball-seat lug bolts).
The 1981-1991 Mercedes-Benz S-Class (W126) uses a 5X112 bolt pattern and a 66.6 mm center bore.
Factory sizes: 14x6.5 +30; 15x7 +25; 16x7 +25; 16x7.5 +20; 16x7.5 +25; 16x8 +20; 17x8.5 +20.
Its wheel fasteners use a M12x1.5 thread.
Bolt-on sizes run from 14" to 18" in diameter; see the size table for the offset range at each width.